Manual Feed Gate Spreader - Setup & Use

Not sure if this is your device? This article is for the Manual Feed Gate Spreader (SKU/Product #: MSS-12721). .
Double-check this info or click here to visit our "Identify My Device" page before you continue.

Getting Started

Congratulations! Now that you have your Manual Feed Gate Spreader, continue reading to learn how to get it up and running!

ASSEMBLY INSTRUCTIONS

MOUNTING BRACKET TO ATV RACK

1. Assemble ATV Bracket by attaching the legs to the bracket using (2) 3/8” x 3-1/2” bolts and nuts. Use 2 of the predrilled options for your specific fit. Mount assembled bracket to ATV Rack using the included 4 U-bolts.

   1. 

2. Install knob into slot with the square spacer inside the slot. Adjust to desired position and hand tighten. Insert Spine into mounted ATV Bracket or UTV/Truck Bracket (accessory, sold separately).

   1. 

MOUNTING DEFLECTION SHIELD AND MANUAL FEED GATE

1. Attach Deflection Shield using (2) 8/32 x 2-1/4” bolts and nuts (note bolt orientation).

   1. 

2. NOTE: This step for Manual Gate ONLY Attach Stiffener to inside Hopper base using (2) 1/4 -20 x 1” bolts, washers and nuts. Attach Feed Gate to Hopper using (1) 3/8 x 1 3/4” bolt and nut (be careful not to over-tighten).

   1. 

ATTACH HOPPER TO SPINE

1. Attach (2) Belly Bands with elongated tabs pointed down to spine using (1) 5/16 x 2-1/2” (partially-threaded) bolt and nut and (1) 5/16 x 3” (fully-threaded) bolt and nut. NOTE: Fully threaded bolt to be installed in top hole.
2. Insert assembled Hopper (with Lid removed) into Belly Bands. (Image A)
3. Attach Hopper to spine using Eye Bolt, ATV Washer (large curved plate), and Nut. (Image B)
4. Connect Belly Bands using the 5/16 x 3” fully-threaded bolt and 3/4” spacer (tighten until there is no space between bands and spacer). (Image C) NOTE: If assembling an ATV Food Plot Spreader Electric Gate proceed to Section F to mount the motor and spin plate.

ATTACHING LEVER AND LINKAGE

1. Attach Lever Arm to Spine using 3/8” x 4.5” bolt, (3) 3/8” washers, spring and nylon nut. Be sure to tighten until spring is fully compressed.
2. Attach Feed Gate to Linkage using washer and cotter pin, then attach complete linkage to Lever Arm using washer and cotter pin.

   1. 

ATTACH SPIN PLATE AND MOTOR

1. Insert ATV Motor through holes in the ATV Motor Arm. Motor should be rotated so that the Control Wire runs toward the ATV. Fasten nuts and washers securely. Secure Spinner Plate with included cotter pin by inserting and bending cotter pin so that it cannot be removed.
2. Install plastic Wire Restraint on any of the back 4 holes in the ATV Motor Arm. The Wire Restraint should be routed with the Control Wire located inside the ATV Motor Arm. Use included bolt and nut to secure Wire Restraint to the Motor Arm.

   1. 

ATTACH RATCHET STRAP

1. Thread provided Ratchet Strap through eyebolt on back of Spreader Spine. Place ratchet strap loops around the front of your ATV rack (close to seat). Adjust tension on Ratchet Strap until firm. Tie off excess strap in a safe place. (See Section B-4 of Operating Instructions.)

   1. 

   2. CAUTION: FAILURE TO PROPERLY CONNECT AND MONITOR THE RATCHET STRAP MAY RESULT IN DAMAGE TO THE ATV OR SPREADER 

OPERATING INSTRUCTIONS

CONNECTING POWER CABLE

1. Make sure the power switch is in the OFF position. Plug the motor power cord into the motor pigtail.
2. Make sure the power switch is still in the OFF position. Attach the alligator clips to your ATV’s battery or plug the lighter plug into your ATV’s 12-volt accessory receptacle (if so equipped).

   1. 

ADDING MATERIAL AND ADJUSTING STRAP

1. Remove lid by placing both hands under the lip of the lid with fingers in the finger grooves. Press upward to remove lid.
2. If using a FieldNode Spreader Screen, make sure it is installed securely, funnel side toward the bottom of the spreader. This heavy-duty plastic Spreader Screen filters and breaks up clumps to prevent clogs.To purchase this accessory or if you have any questions, please visit www.moultrie.com.
3. Add desired material such as feed, fertilizer, seed, etc. to hopper and attach lid.
4. With the material loaded, verify that Ratchet Strap is tight enough to hold the hopper body perpendicular to the ATV rack. Tighten as necessary. (See Section F of Assembly Instructions.)

   1. 

ADJUSTING MATERIAL AMOUNT & OPERATING UNIT

1. 1. Turn the Motor Switch to the ON position.
   2. To spread material, move the Spreader’s Lever Arm up to open the feedgate and move the arm down to close. Reposition Adjustment Stop to set desired Lever position.

      1. 

CLEANING AND STORING UNIT

1. NOTE: FERTILIZER IS EXTREMELY CORROSIVE. After spreading material, completely wash and dry ATV Spreader. A light coat of oil on all metal parts and motor will help prevent rusting and corrosion.

HELPFUL TIPS & POINTERS

(Q) What is the best way to set the dispensing amount?

(A) Set the adjustment stop or controller setting to the position you feel will provide the best coverage for the material being used. Turn on Spreader and open the feed gate. Spread the material for about 20 ft, turn off the spreader and shut the feed gate, and then walk back to verify coverage. Reposition adjustment stop on manual gate controls as needed.