Pro Magnum Series - Setup & Use

Not sure if this is your device? This article is for the Pro Magnum series feeder kit (SKU/Product #: MFG-13445). 
Double-check this info or click here to visit our "Identify My Device" page before you continue.

Note: This article is for the setup of the feeder kit itself, not the hopper assembly. For hopper assembly instructions, go back a section & select our Hopper Setup section.

Getting Started

Congratulations! Now that you have your Pro Magnum feeder kit, continue reading to learn how to get it up and running!

MOUNTING THE FEEDER

From the inside of the drum, put flat washers on the 1/4-20 x 4” Combination Drive Screws then slide through the holes in the bottom of the barrel and screw the push nuts onto the bolts on the outside of the barrel.

Remove battery cover from Super Pro Magnum feeder kit. Turn grooved handle counterclockwise until it releases battery cover and pull downward.

Slide feeder over three Bolts that are sticking firmly through the bottom of the drum. Attach Feeder Kit to the Drum using the three provided Wing Nuts.

INSTALLING BATTERY

Install one or two 6-volt alkaline (ex. Energizer™) or FieldNode rechargeable batteries by attaching the Red Alligator Clip to the postitive terminal (+) and the Black Alligator Clip to the negative (-) terminal. NOTE: Be sure that the Red and Black alligator clips labeled with a “1” are attached to the same battery and that the Red and Black alligator clips labeled with a “2” (if used) are attached to the same battery.

Replace battery cover. Make sure grooved handle is turned counterclockwise, slide cover into place then turn grooved handle clockwise to lock in place. NOTE: Make sure grooved handle is rotated counter-clockwise before trying to install battery housing or else it will not lock into place. 

CONFIGURING AND TESTING FEEDER

1 SET CURRENT TIME

Press the PROGRAM button and SET CURRENT TIME will appear. Press UP or DOWN to set the hour, then press RIGHT to go to the minutes. Press UP or DOWN to set the minutes. Press the BACK button to return to the Main Menu, or press PROGRAM to proceed through the settings.

NOTE: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of the week where each day can be toggled ON/OFF.

 

2 SET CURRENT DAY

Press the PROGRAM button until the Set Current Day screen appears. Press LEFT or RIGHT to select the current day. Press BACK to return to the Main Menu, or press PROGRAM to proceed through the settings.

 

3 SET EST. FEED REMAINING

Press the PROGRAM button until the Est. Feed Remaining screen appears. Press UP or DOWN to select the amount of feed you have in the feeder. Press BACK to return to the Main Menu, or press PROGRAM to proceed through the settings.

 

4 SET FEED TIME

Press the PROGRAM button until the desired Feed Timer appears at the top of the screen. Press the DOWN button until the feed time is flashing. Press PROGRAM to enter edit mode. Press UP or DOWN to set the hour. Press the RIGHT button to go over to the minutes. Press UP or DOWN to set the minutes. Press PROGRAM or BACK to return to the Feed Timer. The factory settings include two feeder times 7am and 6pm, each for 6 seconds.

 

5 SET DAYS OF THE WEEK

After setting the feed time, press UP so the days of the week start flashing. Press PROGRAM to enter edit mode. By default all days should be enabled. Press LEFT or RIGHT to highlight the desired day. Press DOWN to disable the selected day. Press UP to re-enable the selected day. Once all desired days are selected, press PROGRAM or BACK to return to the Feed Timer.

 

6 SET RUN DURATION

Press DOWN and LEFT until the RUN DURATION seconds are flashing. Press PROGRAM to enter edit mode. Press UP or DOWN to set desired feed duration. Press PROGRAM or BACK to return to the Feed Timer.

 

7 SET MOTOR SPEED

Press UP or DOWN until the motor speed setting is flashing at the bottom of the screen. Press PROGRAM to enter edit mode. Press RIGHT or LEFT to select the desired motor setting. Press PROGRAM or BACK to return to the Feed Timer.

When the Feed Timer is blinking at the top of the screen, press PROGRAM or RIGHT to advance to the next feed timer. Repeat for all required feed times.

 

8 TEST FEEDER

Press the BACK button to reach the Main Menu. Press the TEST button to enter the Test Mode. The Test duration will appear (this will be the same as the duration as Feed Timer 1). Press UP or DOWN to set the Test Duration. Press PROGRAM. Press RIGHT or LEFT to select desired motor speed. Press PROGRAM to perform test. After a 5 second countdown, the test will commence.